Laboratory Autoclave

CONSTRUCTION

Inner Chamber Made of  SS 304 Grade SS Sheet, 16 SWG

Outer Chamber  SS 304 Grade 1 mm thick Sheet

Boiler and Outer shell provided with air insulation

HEATING SYSTEM

6000 Watts 2” SS BSP Heater made of  High quality A1 Kanthal Wire used for better heating.

DOORS

Top Loading 6 mm Thick SS 304 grade Metal Door with Safety Valve 2 Nos, 1 Pressure Indicating Gauge, 1 Pressure Release Valve, 1 Vacuum Valve with Door Open With Foot Lifting Arrangement

OPERRATING PRESSURE

15 psi

DESIGN PRESSURE

Up to 40 PSI

TEMPERATURE RANGE Above Ambient °C to 130°C

Temperature Resolution 0.1°C

Temperature Accuracy ± 0.5°C  and Temperature Uniformity ±1

Full sterilization cycle including air purging, sterilizing hold time & End with steam Exhaust of Pressure

WATER LAVEL CIRCUIT Low water level alarm with Heater cut off

SENSOR 3/8” BSP SS 304 grade PT 100 Sensor

CONTROL SYSTEM -Digital Indicating Temperature Controller Cum Timer along with thermocouple sensor AND Automatic Steam purging and Steam Release after Cycle complete with Solenoid Valve 

A separate Control Box made of SS. sheet

• Vertical Autoclave is widely used in Microbiology, Medicine, Waste treatment, Pharma QC / QA / R & D and all applications requiring sterilization.
• Double walled construction with inner chamber (boiler) made of 304 grade stainless steel 16 SWG sheet and outer shell of 304 grade stainless steel sheet with mirror polish.
• The boiler and outer shell is provided with air insulation.
• Lid is made of die pressed thick stainless steel plate & is equipped with pressure gauge, steam release / exhaust valve & spring loaded safety valves.
• Foot lifting arrangement for the lid.
• Fully argon welded to avoid steam and pressure leakage.
• Heavy duty industrial flange heaters.
• Full sterilization cycle including air purging, sterilizing hold time, cycle end with release / exhaust of pressure & alarm is automatic.
• Microprocessor based controller with time and temperature programmable by user.
• Temperature Sensor: PT-100.
• Low water level alarm with heater cut off.
• Perforated basket made of 304 grade stainless steel sheet.

Technical Data:

WORKING CHAMBR – 20 Ltr Capacity

12” X 12” Dia x  Height        

CONSTRUCTION

Inner Chamber Made of  SS 304 Grade SS Sheet, 16 SWG

HEATING SYSTEM

1500 Watts 1 1/4" SS BSP Heater made of  High quality A1 Kanthal Wire used for better heating.

Door Top Loading 6 mm Thick SS 304 grade Metal Door with Safety Valve 1 Nos, 1 Pressure Indicating Gauge, 1 Pressure Release Valve,

OPERRATING PRESSURE

15 psi

DESIGN PRESSURE

Up to 40 PSI

TEMPERATURE RANGE Above Ambient °C to 130°C

Temperature Resolution 0.1°C

Temperature Accuracy ± 0.5°C  and Temp.

SENSOR 1/4” BSP SS 304 grade PT 100 Sensor

CONTROL SYSTEM -Digital Indicating Temperature Controller Cum Timer along with thermocouple sensor

A separate Control Box made of SS. sheet

It will consist of indicating lamps for Mains On/Off, SSR for Heaters; Main & Terminal Strips etc.

FEATURE -MCB for electrical safety.

Supply 230V AC. Single Phase, 50Hz

It is used for sterilization under saturated steam pressure at any selected point between 5 to 20 p.s.i. (optional adjustable with pressure control switch). These are double walled units with inner chamber (Boiler) made of 18 S.W.G. SS & outer chamber is covered with M.S. Lid with S.S. lining is tightened by locking system. Fitted with neoprene rubber gasket, all system are hydraulically tested upto 40 p.s.i. as a safety measure. All autoclaves are fitted with standard accessories such as water level indicator, pressure gauge, steam release cock. Spring loaded safety valve & heating element. Supplied completed with S.S. Basket, cord and plug to work on 220/230 volts A. C. Supply. All Models besides being fitted with SS/lid & having inner chamber made of S.S. & outer chamber S.S. are also fitted with vacuum beaker as a safety Device. With S.S. Basket

Technical Specification

Autoclave is double walled complete made of S.S.304, Inner & outer with Foot Lifting Arrangement & heavy gauge Dia press lid fitted with 2 safety valve, 1 Steam Release Valve & pressure gauge.

Working Pressure : UPTO 15 PSI

Working Temp  : 121 ˚C to 125 ˚C

Temp. controlled By : PID Controller with timer & purging system PID controller

Solenoid Valve Systems : This Valve work for automatic Purging & Automatic Steam Release when cycle Time is Complete

Safety Protection for heater : Low water Level cut off systems to cut off Heater when water level is Not Proper.

S. S. Perforated basket to keep Material

It is used for sterilization under saturated steam pressure at any selected point between 5 to 20 p.s.i. (optional adjustable with pressure control switch). These are double walled units with inner chamber (Boiler) made of 18 S.W.G. SS & outer chamber is covered with M.S. Lid with S.S. lining is tightened by locking system. Fitted with neoprene rubber gasket, all system are hydraulically tested upto 40 p.s.i. as a safety measure. All autoclaves are fitted with standard accessories such as water level indicator, pressure gauge, steam release cock. Spring loaded safety valve & heating element. Supplied completed with S.S. Basket, cord and plug to work on 220/230 volts A. C. Supply. All Models besides being fitted with SS/lid & having inner chamber made of S.S. & outer chamber S.S. are also fitted with vacuum beaker as a safety Device. With S.S. Basket

Technical Specification

Autoclave is double walled complete made of S.S.304, Inner & outer with Foot Lifting Arrangement & heavy gauge Dia press lid fitted with 2 safety valve, 1 Steam Release Valve & pressure gauge.

Working Pressure : UPTO 15 PSI

Working Temp  : 121 ˚C to 125 ˚C

Temp. controlled By : PID Controller with timer & purging system PID controller

Solenoid Valve Systems : This Valve work for automatic Purging & Automatic Steam Release when cycle Time is Complete

Safety Protection for heater : Low water Level cut off systems to cut off Heater when water level is Not Proper.

S. S. Perforated basket to keep Material

• Production Capacity: 10
• Delivery Time: 2 to 3 weeks